Heat Treatment - Harry Bhadeshia

Heat Treatment R. Manna Assistant Professor Centre of Advanced Study Department of Metallurgical Engineering Institute of Technology Banaras Hindu University Varanasi-221 005, India [email protected] Tata Steel-TRAERF Faculty Fellowship Visiting Scholar Department of Materials Science and Metallurgy University of Cambridge Pembroke Street, Cambridge, CB2 3QZ

[email protected] HEAT TREATMENT Fundamentals Fe-C equilibrium diagram. Isothermal and continuous cooling transformation diagrams for plain carbon and alloy steels. Microstructure and mechanical properties of pearlite, bainite and martensite. Austenitic grain size. Hardenability, its measurement and control. Processes Annealing, normalising and hardening of steels, quenching media, tempering. Homogenisation. Dimensional and compositional changes during heat treatment. Residual stresses and decarburisation.

2 Surface Hardening Case carburising, nitriding, carbonitriding, induction and flame hardening processes. Special Grade Steels Stainless steels, high speed tool steels, maraging steels, high strength low alloy steels. Cast irons White, gray and spheroidal graphitic cast irons Nonferrous Metals Annealing of cold worked metals. Recovery, recrystallisation and grain growth. Heat treatment of aluminum, copper, magnesium, titanium and nickel alloys. Temper designations for aluminum and magnesium alloys.

Controlled Atmospheres Oxidizing, reducing and neutral atmospheres. 3 Suggested Reading R. E. Reed-Hill and R. Abbaschian: Physical Metallurgy Principles, PWS , Publishing Company, Boston, Third Edition. Vijendra Singh: Heat treatment of Metals, Standard Publishers Distributors, Delhi. Anil Kumar Sinha: Physical Metallurgy Handbook, McGrawHill Publication. H. K. D. H. Bhadeshia and R. W. K. Honeycombe: SteelsMicrostructure and Properties, Butterworth-Heinemann, Third Edition, 2006 R. C. Sharma: Principles of Heat Treatment of Steels, New Age International (P) Ltd. Publisher.

Charlie R. Brooks: Heat Treatment: Structure and Properties of 4 Nonferrous Alloys, A. S. M. Publication. Definition of heat treatment Heat treatment is an operation or combination of operations involving heating at a specific rate, soaking at a temperature for a period of time and cooling at some specified rate. The aim is to obtain a desired microstructure to achieve certain predetermined properties (physical, mechanical, magnetic or electrical). 5

Objectives of heat treatment (heat treatment processes) The major objectives are to increase strength, harness and wear resistance (bulk hardening, surface hardening) to increase ductility and softness (tempering, recrystallization annealing) to increase toughness (tempering, recrystallization annealing) to obtain fine grain size (recrystallization annealing, full annealing, normalising) to remove internal stresses induced by differential deformation by cold working, non-uniform cooling from high temperature during6 casting and welding (stress relief annealing) to improve machineability (full annealing and normalising)

to improve cutting properties of tool steels (hardening and tempering) to improve surface properties (surface hardening, corrosion resistance-stabilising treatment and high temperature resistance-precipitation hardening, surface treatment) to improve electrical properties (recrystallization, tempering, age hardening) to improve magnetic properties (hardening, phase transformation) 7 Fe-cementite metastable phase diagram (Fig.1) consists of phases liquid iron(L), -ferrite, or austenite, -ferrite and Fe3C or cementite and phase mixture of pearlite

(interpenetrating bi-crystals of ferrite and cementite)(P) and ledeburite (mixture of austenite and cementite)(LB). Solid phases/phase mixtures are described here. 8 Fig.1: Fe-Cementite metastable phase diagram (microstructural) +L A5=1495C 0.09

0.17 + 0.53 1227C L+I 2.11

cm A B A2 =668/ 770C C A3 I+ 0.77

0.00005 L+CmI LB+CmI I(II+CmII)+LB (eu(II +CmII)+Cmeu) D II+CmII

0.0218 I+ (P(ed P(ed+Cmed) +CmII +Cmed) +CmIII 4.30 I+LB A 910C

Pearlite Temperature, C 1394C L=liquid, Cm=cementite, LB=ledeburite, =delta ferrite, = alpha ferrite, = alpha ferrite(0.00005 wt%C) =austenite, P=pearlite, eu=eutectic, ed=eutectoid, I=primary, II=secondary, III=tertiary

L (P(ed+Cmed)+CmII)+ LB (P(ed+Cmed) +CmII+Cmeu) I(+CmIII)+ P( ( (P(ed(ed+CmIII)+Cmed) +CmII)+ ed ed (P(ed(ed+C +Cm )+Cm ) LB ((P( ( +Cm )+Cm ) III ed ed ed

III ed mIII)+Cmed) +Cm +Cm )+Cm ) II II eu Weight percent carbon Ledeburite=LB(eu+Ceu)

1539C LB (eu(II +CmII)+Cmeu) +CmI E A4=1147C F Cm LB (P(ed+Cmed)

+CmII)+Cmeu)+CmI A1=727C LB ((P(ed(ed+CmIII) +Cmed) +CmII)+ Cmeu) +CmI Ao=210C 6.67 9 ferrite: Interstitial solid solution of carbon in iron of body centred cubic crystal structure (Fig .2(a)) ( iron ) of higher lattice parameter (2.89) having solubility limit of 0.09 wt% at

1495C with respect to austenite. The stability of the phase ranges between 1394-1539C. Fig.2(a): Crystal structure of ferrite This is not stable at room temperature in plain carbon steel. However it can be present at room temperature in alloy steel specially duplex stainless steel. 10 phase or austenite: Interstitial solid solution of carbon in iron of face centred cubic crystal structure (Fig.3(a)) having solubility limit of 2.11 wt% at 1147C with respect to cementite. The stability of the phase ranges

between 727-1495C and solubility ranges 0-0.77 wt%C with respect to alpha ferrite and 0.77-2.11 wt% C with respect to cementite, at 0 wt %C the stability ranges from 910-1394C. Fig.3(a ): Crystal structure of austenite is shown at right side. 11 Fig. 3(b): Polished sample held at austenitisation temperature. Grooves develop at the prior austenite grain boundaries due to the balancing of surface tensions at grain junctions with the free surface. Micrograph courtesy of Saurabh Chatterjee. 12

-ferrite: Interstitial solid solution of carbon in iron of body centred cubic crystal structure ( iron )(same as Fig. 2(a)) having solubility limit of 0.0218 wt % C at 727C with respect to austenite. The stability of the phase ranges between low temperatures to 910C, and solubility ranges 0.00005 wt % C at room temperature to 0.0218 wt%C at 727C with respect to cementite. There are two morphologies can be observed under equilibrium transformation or in low under undercooling condition in low carbon plain carbon steels. These are intergranular allotriomorphs ()(Fig. 4-7) or intragranular

idiomorphs(I) (Fig. 4, Fig. 8) 13 Fig. 4: Schematic diagram of grain boundary allotriomoph ferrite, and intragranular idiomorph ferrite. 14 Fig.5: An allotriomorph of ferrite in a sample which is partially transformed into and then quenched so that the remaining undergoes martensitic transformation. The allotriomorph grows rapidly along the austenite grain boundary (which is an easy diffusion path) but thickens more slowly.

15 Fig.6: Allotriomorphic ferrite in a Fe-0.4C steel which is slowly cooled; the remaining dark-etching microstructure is fine pearlite. Note that although some -particles might be identified as idiomorphs, they could represent sections of allotriomorphs. Micrograph courtesy of the DOITPOMS project. 16 Fig.7: The allotriomorphs have in this slowly cooled low-carbon steel have consumed most of the austenite before the remainder transforms into a small amount of pearlite. Micrograph courtesy of the DoITPOMS project. The shape of the ferrite is now determined by the impingement of particles which grow from different nucleation sites. 17

Fig. 8: An idiomorph of ferrite in a sample which is partially transformed into and then quenched so that the remaining undergoes martensitic transformation. The idiomorph is crystallographically facetted. 18 There are three more allotropes for pure iron that form under different conditions -iron: The iron having hexagonal close packed structure. This forms at extreme pressure,110 kbars and 490C. It exists at the centre of the Earth in solid state at around 6000C and 3 million atmosphere pressure.

FCT iron: This is face centred tetragonal iron. This is coherently deposited iron grown as thin film on a {100} plane of copper substrate Trigonal iron: Growing iron on misfiting {111} surface of a face centred cubic copper substrate. 19 Fe3C or cementite: Interstitial intermetallic compound of C & Fe with a carbon content of 6.67 wt% and orthorhombic structure consisting of 12 iron atoms and 4 carbon atoms in the unit cell. Stability of the phase ranges from low temperatures to 1227C

Fig.9(a): Orthorhombic crystal structure of cementite. The purple atoms represent carbon. Each carbon atom is surronded by eight iron atoms. Each iron atom is connected to three carbon atoms. 20 Fig.9(b): The pearlite is resolved in some regions where the sectioning plane makes a glancing angle to the lamellae. The lediburite eutectic is highlighted by the arrows. At high temperatures this is a mixture of austenite and cementite formed from liquid. The austenite subsequently decomposes to pearlite. Courtesy of Ben Dennis-Smither, Frank Clarke and Mohamed Sherif 21 Critical temperatures:

A=arret means arrest A0= a subcritical temperature ( A5=Peritectic temperature=1495C 22 Acm=/+cementite phase field boundary=composition dependent =727-1147C In addition the subscripts c or r are used to indicate that the temperature is measured during heating or cooling respectively.

c=chaffauge means heating, Ac r=refroidissement means cooling, Ar Types/morphologies of phases in Fe-Fe3C system Cementite=primary (CmI), eutectic (Cmeu), secondary (CmII)(grain boundary allotriomophs, idiomorphs), eutectoid (Cmed) and tertiary(CmIII). Austenite= austenite()(equiaxed), primary (I), eutectic (eu), secondary (II) (proeutectoid), -ferrite=ferrite () (equiaxed), proeutectoid or primary (grain boundary allotriomorphs and idiomorphs)(I), eutectoid(eu) and ferrite (lean in carbon) (). Phase mixtures Pearlite (P) and ledeburite(LB)

23 Important Reactions Peritectic reaction Liquid+Solid1Solid2 L(0.53wt%C)+(0.09wt%C)(0.17wt%C) at 1495C Liquid-18.18wt% +-ferrite 81.82 wt%100 wt% Fig.10: -ferrite in dendrite form in as-cast Fe-0.4C2Mn-0.5Si-2 Al0.5Cu, Coutesy of S. Chaterjee et al. M. Muruganath, H. K. D. H. Bhadeshia 24 Eutectic reaction LiquidSolid1+Solid2

Liquid (4.3wt%C) (2.11wt%C) + Fe3C (6.67wt%C) at 1147C Liquid-100 wt% 51.97wt% +Fe3C (48.11wt%) The phase mixture of austenite and cementite formed at eutectic temperature is called ledeburite. Fig.11: Microstructure of white cast iron containing massive cementite (white) and pearlite etched with 4% nital, 100x. After Mrs. Janina Radzikowska, Foundry Research lnstitute in Krakw, Poland 25 Fig. 12: High magnification view (400x) of the white cast iron specimen shown in Fig. 11, etched with 4% nital. After Mrs.

Janina Radzikowska, Foundry Research lnstitute in Krakw, Poland 26 Fig. 13: High magnification view (400x) of the white cast iron specimen shown in Fig. 11, etched with alkaline sodium picrate. After Mrs. Janina Radzikowska, Foundry Research lnstitute in Krakw, Poland 27 Eutectoid reaction Solid1Solid2+Solid3

(0.77wt%C) (0.0218wt%C) + Fe3C(6.67wt%C) at 727C (100 wt%) (89 wt% ) +Fe3C(11wt%) Typical density ferrite=7.87 gcm-3 Fe3C=7.7 gcm-3 volume ratio of - ferrite:Fe3C=7.9:1 28 Fig. 14: The process by which a colony of pearlite evolves in a hypoeutectoid steel. 29 Fig. 15 : The appearance of a pearlitic

microstructure under optical microscope. 30 Fig. 16: A cabbage filled with water analogy of the threedimensional structure of a single colony of pearlite, an interpenetrating bi-crystal of ferrite and cementite. 31 Fig. 17: Optical micrograph showing colonies of pearlite . Courtesy of S. S. Babu. 32 Fig. 18: Transmission electron micrograph of extremely fine pearlite. 33

Fig.19: Optical micrograph of extremely fine pearlite from the same sample as used to create Fig. 18. The individual lamellae cannot now be resolved. 34 Evolution of microstructure (equilibrium cooling) Sequence of evolution of microstructure can be described by the projected cooling on compositions A, B, C, D, E, F. At composition A L +L +

At composition B L +L L+I I + +I +CmIII I+ (P(ed+Cmed)

I(+CmIII)+(P(ed(ed+CmIII)+Cmed) 35 At composition C L L+I II+CmII P(ed+Cmed)+CmII P(ed (ed+CmIII)+Cmed)+CmII

At composition D L L+I I+LB I(II+CmII)+LB (eu(II+CmII)+Cmeu) (P(ed+Cmed)+CmII)+ LB (P(ed+Cmed)+CmII+Cmeu) (P(ed(ed+CmIII)+Cmed) +CmII)+ LB ((P(ed(ed+CmIII)+Cme +CmII)+Cmeu) 36

At composition E L+CmI LB(eu+Cmeu+CmI L LB (eu(II+CmII)+Cmeu)+CmI LB (P(ed+Cmed)+CmII)+Cmeu)+CmI LB ((P(ed(ed+CmIII)+Cmed) +CmII)+ Cmeu)+CmI At composition F L Fe3C 37 Limitations of equilibrium phase diagram

Fe-Fe3C equilibrium/metastable phase diagram Stability of the phases under equilibrium condition only. It does not give any information about other metastable phases. i.e. bainite, martensite It does not indicate the possibilities of suppression of proeutectoid phase separation. No information about kinetics No information about size No information on properties. 38

Recently Viewed Presentations

  • ECE 5984: Introduction to Machine Learning

    ECE 5984: Introduction to Machine Learning

    Input gives weight for filter. Sum where output overlaps. Learnable Upsampling: Transpose Convolution. 3 x 3 . transpose. convolution, stride 2 pad 1. Filter moves 2 pixels in the output for every one pixel in the input
  • Foreign Guest Workers or Domestic Workers? Farm Labor ...

    Foreign Guest Workers or Domestic Workers? Farm Labor ...

    Farmworkers with more years in farm work or experienced farmworkers more likely to stay longer. H-2A program farmworkers stay longer. Non-farm job prospect. Table 15a. Able to get a U.S. non-farm job within a month? Get Non-farm Job Within A...
  • The Mask of Janus - University of Liverpool

    The Mask of Janus - University of Liverpool

    Arial Calibri Default Design The Mask of Janus Janus - the Roman god who looked two ways at once Personal Perspective The Shanghai Conference, 1909 Hague Convention 1912-14 Allied invasion of Sicily 1943 The French Connection All downhill from here…
  • RNG Overview - Computer Science and Engineering

    RNG Overview - Computer Science and Engineering

    (from EDAS) Region Authors (%) United States 65.0% Europe, Middle East, Africa 18.1% Asia/Pacific 12.9% Canada 3.6% Latin America 0.5% Top Three Outstanding Papers: Selection Committee Don Towsley K.K.Ramakrishnan Steven Low Mingyan Liu Jorg Liebeherr Top Three Outstanding Papers are...
  • TWIC DHS IRB Briefing - United States Coast Guard

    TWIC DHS IRB Briefing - United States Coast Guard

    In the maritime domain, preventing incidents has been a core mission of the CG for a long time. MTSA emphasized the Coast Guard's security-specific mission and gave it broad authorities for MTSA implementation in the maritime arena. While the CG...
  • Ratatat Project Report Tony Toole 19th October 2009

    Ratatat Project Report Tony Toole 19th October 2009

    Ratatat Project Report Tony Toole 19th October 2009 Aims and Objectives The broad aim of the Ratatat project is to create an online learning environment that allows vocational and work-based postgraduate learners to remotely access and carry out sophisticated practical...
  • Forms of Poetry

    Forms of Poetry

    Haiku Example A rain drop, drop top I just wanna eat nonstop Feed me a pork chop 13. Quatrain (form) Is not some strange train that is taken to "The Land of Qua." "Quatr" means 4 Has 4 lines with...
  • CourseDen Orientation CourseDen uwgonline.westga.edu eCore  Online Core Classes

    CourseDen Orientation CourseDen uwgonline.westga.edu eCore Online Core Classes

    eCore. Synchronous 8 & 16 week sessions. Fulfills ALL core areas (A - E) Transferable to all USG institutions. Seats are always available. If interested, contact NakitaHogans at 678-839-6091