# L 10 Torque and Angular Momentun - Physics & Astronomy

L-10 Torque and Rotational Motion Torque makes things spin! What makes something rotate in the first place? TORQUE How do I apply a force to make the rod rotate about the axel? Not just anywhere!

AXEL TORQUE To make an object rotate, a force must be applied in the right place. the combination of force and point of application is called TORQUE lever arm, L

Axle Force, F Torque = force times lever arm Torque = F L Torque example F

L What is the torque on a bolt applied with a wrench that has a lever arm of 30 cm with a force of 10 N? Torque = F L = 30 N 0.30 m =9Nm

For the same force, you get more torque with a bigger wrench the job is easier! Homer attempts to straighten out the leaning tower of Pisa lever folcrum

Net Force = 0 , Net Torque 0 10 N 10 N > The net force = 0, since the forces are applied in opposite directions so it will not accelerate. > However, together these forces will make the rod rotate in the clockwise direction.

Net torque = 0, net force 0 The rod will accelerate upward under these two forces, but will not rotate. Balancing torques 20 N 10 N

1m 0.5 m Left torque = 10 N x 1 m = 10 n m Right torque = 20 N x 0.5 m = 10 N m Equilibrium To ensure that an object does not

accelerate or rotate two conditions must be met: net force = 0 net torque = 0 this results in the practical 4-1 ladder rule When is an object stable?

If you can tip it over a bit and it doesnt fall The object may wobble a bit but it eventually stops and settles down to its upright position. Why things fall over Every object has a special point called the center of gravity (CG). The CG is usually right smack in the center of the object. if the center of gravity is supported, the

object will not fall over. You generally want a running back with a low CG then its harder to knock him down. The lower the CG the more stable an object is. stable not easy to knock over! Condition for stability If the CG is above the edge, the object

will not fall CG when does it fall over? CG STABLE CG

NOT STABLE If the vertical line extending down from the CG is inside the edge the object will return to its upright position the torque due to gravity brings

it back. Stable and Unstable stable torque due to gravity pulls object back unstable torque due to gravity

pulls object down Stable structures Structures are wider at their base to lower their center of gravity Playing with your blocks CG

If the center of gravity is supported, the blocks do not fall over Object with low CG 300 lb fullback who is 4 ft, 10 inches tall and runs a 4-40 Stay low to the ground!

High Profile Vehicles wind As more and more stuff is loaded into a semi, its center of gravity moves upward. It could be susceptible to tipping over.

The shape of an object determines how easy or hard it is to spin Hinge For objects of the same mass, the longer one is tougher to spin takes more torque It matters where the hinge is The stick with the hinge at the end takes 4 times

more torque to get it spinning than the stick with the hinge in the center. Rotational Inertia (moment of inertia) Rotational inertia is a parameter that is used to quantify how much torque it takes to get a particular object rotating it depends not only on the mass of the object, but where the mass is relative to

the hinge or axis of rotation the rotational inertia is bigger, if more mass is located farther from the axis. How fast does it spin? For spinning or rotational motion, the rotational inertia of an object plays the same role as ordinary mass for simple motion For a given amount of torque applied to an

object, its rotational inertia determines its rotational acceleration the smaller the rotational inertia, the bigger the rotational acceleration Same torque, different rotational inertia Big rotational

inertia Small rotational inertia spins slow spins fast

rotational inertia - examples Suppose we have a rod of mass 2 kg and length 1 meter with the axis through the center Its moment of inertia is 2 units Imagine now that we take the same rod and stretch it out to 2 meters; its mass is, of course, the same. Its moment of inertia is 4 units

rotational inertia examples Rods of equal mass and length axes through center axes through end Rotational inertia of 1 unit

Rotational inertia of 4 units

## Recently Viewed Presentations

• Effective and familiar use of antidote with vitamin K should a severe bleed occur whilst being treated. ... is the most crucial aspect of NOAC Rx (reinforce at every FU) Routine monitoring: Hb and liver function (annually) ... PowerPoint Presentation
• NEMSIS Version 3 Data Dictionary. The NEMSIS Version 3 Data Dictionary is a document describing in detail each of the 578 Version 3 Data Elements.The Data Dictionary is a consolidated source of information for each data elements.
• "The IEP team mustâ€”* * * (iii) in the case of a child who is blind or visually impaired, provide for instruction in Braille and the use of Braille unless the IEP team determines, after an evaluation of the child's...
• Atmosphere foldable Use pages 479-480 . Cover page and name . Page 1 draw and label a picture of the layers of the atmosphere. Page 2 describe the troposphere and give it's range of altitude and temperature
• Important features of Newman's clustering algorithm. The number and size of the clusters are determined by the algorithm. Attempts to find a division that maximizes a modularity score Q . heuristic algorithm. Notifies when the network is non-modular
• Project Director is the applicant. Duration of 1 to 3 years. Valued between \$75K and \$200K. ... Some special initiatives that are offered through PG and PDG include the Kanishka Project, the Belmont Forum, and the Mitacs-Accelerate Internship program.
• The Is-a Rule? Activity: Create a Domain Model for Your Project Identify nouns and noun phrasesâ€”for inspiration USs are good starting place Collaboratively sketch class diagram Use as inspiration for MVC Model class design
• As each of the first six seals were broken, severe judgments fell upon the globe, and one fourthof the population of the earth was killed.The unbelieving inhabitants of the earth became convinced of the reality of the God of Heaven,...